Having problems with your KDS K717s 17" LCD Monitor ?

KDS K717s 17" LCD Monitor

\015 I have had it a bout a year now.i turned my computer off before bed.started it the next day the tower come on but nothing from the monitor.Ive plugged my old CRT monitor in and it work fine.when i plug the LCD monitor i get nothing.no light form the button or anything.any ideas?thanks.\015

Answers :

This is a common problem across many monitors, unfortunately. The problem stems from one of two things, typically.

Itis either the Power Inverter board (Inverter Mirage Electronics AD-1700Rev:F 200-000-170DTL1 VERSION:A) or a weak or dying backlight.

Ifyour monitor comes on for a few seconds then you can test the backlight byusing the controls to get into the backlight brightnes settings on theOSD and turning it WAY down.

If that doesn't work or if it won't come on at all then it islikely bad capacitors on the Power board mentioned above. If you feeladventurous and know how to solder then you might be able to fix thisyourself. You need to be careful however because you are dealing withhigh voltage in there and capacitors CAN hold a charge long after youhave unplugged the unit. You can read more about this power board aswell as how to replace the bad caps HERE.

Ifthat's not for you then I would recommend taking it to a local TV shopfor them to fix. The parts shouldn't be more than $20, but labor can beexpensive.
Repair Help & Product Troubleshooting for KDS K717s 17" LCD Monitor

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

KDS K717s 17" LCD Monitor


This is a common problem across many monitors, unfortunately. The problem stems from one of two things, typically. Itis either the Power Inverter board (Inverter Mirage Electronics AD-1700Rev:F 200-000-170DTL1 VERSION:A) or a weak or dyin ... KDS K717s 17" LCD Monitor

The monitor goes blank after just a few seconds or sometimes works for hours.


Two possible causes are bad capacitors or a bad light inside the LCD panel.\015\012\015\012Open the unit and check to see if any of the capacitors in the power supplyor other boards look domed or vented on the top.\015\012\015 ... ViewSonic VX924 19" LCD Monitor

Can my KDS (#K717S-700P) monitor be wall mounted?


Can my KDS (#K717S-700P) monitor be wall mounted?\012 This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny.com can find those parts ... KDS K717s 17" LCD Monitor

My kds k-92mdwb monitor goes black after a few seconds. How can I fix this?


Brendadeese, You might be able to repair it. Well your husband or boyfriend maybe. If good with a soldering iron, solder-wick, solder, and $5-$12 in new filter capacitors. You should have visited YOUTUBE for video clips of "LCD monitor disassembly"an ... KDS K92mdwb Monitor

KDS K717s LCD screen goes white


Most repair shops would start with replacing the controller board. ... KDS K717s 17" LCD Monitor

How do I get crayon off the monitor - KDS K717s 17" LCD Monitor


Sorry that you're having trouble.Is it a little or a lot?Try any of these on a small inconspicous spot:1) you might be able to gently remove it with a simple pencil eraser.2) you might try some diluted ... KDS K717s 17" LCD Monitor

Picture won't say on 19" silver monitor - KDS K717s 17" LCD Monitor


That has something to do (defect) with your power section of the main board. ... KDS K717s 17" LCD Monitor

Problem started with a white screen, now It just remains black, installed my old monitor, works fine, put the KDS back in line, no picture, just black tried on off on the monitor and on the computer, checked and rechecked all connections, it just don't work, put my old Compaq monitor on, fires right up. Trash?


Jimmoser45, Could be trash! Could be a Trade-in on a new monitor! Try to follow me on this will-ya!!! You take your K226WDB to store and maybe get $10 knocked off the new one? Anyhow, you walk out with new LCD display and 1, poss 2yrs warranty. But t ... KDS K226WDB Monitor

Image extends beyond KDS 22" LCD monitor even at minimum size


Use monitor factory reset option ... KDS K22mdwb LCD Monitor

Kds model 780 monitor no signal, power button does not work


My monitor does the same thing at times and sometimes shows "No Signal" and at other times the screen will maintain the images but the backgound color switches to mustard yellow. In each of these cases I have been able to solve the problem by unplugg ... KDS Radius RAD-5 15 in. Flat Panel LCD Monitor

WE need the AC adapter for a KDS monitor gamerguy51, you are wrong! The Rad 5 model of the 15 inch LCD monitor made by KDS requires an AC Adptor 12V 32W 3A which connects via a small jumper off the back side of the monitors connector with to the Display Adapter. I have a KDS Rad 5 monitor, but can't find the required adaptor. Can anyone help me?


Http://www.12vadapters.com/adapter/power-supply/12v/for-lcd-screens/hyundai-b70d-2.html ... KDS RAD-5GS 15" Flat Panel LCD Monitor

My monitor turns white when i turn it on every


Your monitor is about to go out. It may be a faulty bulb if an older monitor or if a newer one which utilizes a plasma or lcd screen, the liquid crystals maybe going bad or the light source could be going bad as well. When LCD's or Plasmas start goi ... BenQ FP71E 17" LCD Monitor

I get error message: Out of Range, on my 17 inch LCD KDS monitor


Get the monitor that you used previously, and on the Windows desktop, go to display properties, in settings> advanced, under the monitor tab, change the refresh rate to 60, which is common on these flat panels. ... KDS Computer Monitors

Kds 917s lcd monitor


Yup, that's correct. The capacitors are very cheaply made. I recommend replacing them all if applicable. Before replacing them you must allow the capacitors to discharge. You can just unplug the monitor for a few days. A manual way is possible. I wil ... KDS K717s 17" LCD Monitor

Kds 700p monitor


The most common problem with LCD monitors is the capacitors that are on the power pack. the pack usually looses or pops as we say 2-6 of them after 3-5 years. its almost a certainty after 5 years. a component repair tech can replace these but unless ... KDS K717s 17" LCD Monitor

My monitor stays on for 6 seconds


Hello,You have a monitor with a common problem. After a few years some LCD monitors will\015\012blow a power supply. The problem is caused by parts called capacitors\015\012overheating in the confined space of he monitor. If you are good ... KDS Radius RAD-7 17" Flat Panel LCD Monitor

Kds vs-f14 my lcd monitor kds vs-f14 has no picture but has a dim light ,i found a smd resistance R114 burnt , i donnot know value of this resistance,please tel me the value and any suggestio for repairing the monitor thanks a lot


There is usually an identical resistor somewhere else on the circuit board, so if you cannot read the colors of the burnt one, you can read the colors from an identical resistor on the same board. If you just replace the resistor, it will probably ju ... BenQ FP731 17" LCD Monitor

KDS Rad-9p wont stay on


My monitor will not work it will come on when the pc is cut on but it will not display ... KDS Radius RAD-9p 19" Flat Panel LCD Monitor

Monitor shaking problem but dont think its the monitor!


If both monitors are shaking,problem is with video card or motherboard,you might try loading specific drivers for your video card or try changib=ng refresh rates.\015\012Please rate the solution and provide feedback.\015\012Samir ... BenQ FP71E 17" LCD Monitor

When computer is booting up, the monitor goes out before it gets all the way up and says the Horizontal, and Vertical is out of range. The menu says that the freq. is now Hor. freq. 91.1 KHZ, and Vert. Freq. is 81 HZ. I cannot do anything with the cursor for turning the computer off or trying to try to fix the problem. My son gave me this monitor today, and this is what happened when I connected it to my computer. It is a KDS 17'' LCD color monitor. Factory ID: GS Power source is DC 12.0 DC 3.5


Hello,Turn the monitor on without turning computer on. Use the OSD (On Screen Display to lower the refresh frequencies. On the monitor look for a Setup button. The arrows allow you to scroll through the options. Do not forget to save settings. ... Computer Monitors

KDS Silver 17 inch monitor


Several of these monitors I have repaired from green light "blinking" and also no light / black screen.In many cases I found bad filter Caps after the switching regulator. The ratings seem insufficient to handle the convection cooling. I replac ... KDS 17S 17" Monitor

I have a older kds lcd monitor that goes black less than 1 min after turning on, the power light stays on, the monitor will come back on if you repower the monitor then goes back off in 3 or 4 seconds. Is there a easy fix or should I replace the monitor ?


If you look closely can you see a very dark image on the screen? your problem is usually the result of the backlight on its way out, these are very hard to replace so you will need to take it to a profesional, in most cases it is cheeper to buy a new ... KDS Computer Monitors

The screen on my laptop computer has become dark. If I shine a light on the screen I can barely see the display and if I connect an external monitor to the computer I get a display on the remote monitor. The computer is a KDS Computers model Valiant 671XH laptop.


The LCD display connection is loose. Try reconnecting this and the display will be fine. The connection should be at the top of the base right above the keyboard under the plastics. ... PC Laptops

The monitor goes blank after just a few seconds or sometimes works for hours.


The monitor goes blank after just a few seconds or sometimes works for hours?\012 This trouble maybe power supply or inverter boards is defective.\012 first you can test the voltage of the multr,and then check which part is defective.From Wisiny. ... KDS K717s 17" LCD Monitor

I have a KDS 15" LCD monitor. It has not plug and on the specification plaque on the bottom says 12V 2Amp power source. I have a plug with an output of 12V 2000MA but both are female and the power supply has the negative polarity on the outter part of the plug. So does it matter what the polarity is on the monitor and is 2amps the same as 2000 milli amps? Assuming I can find an adapter.


... KDS RAD-5GS 15" Flat Panel LCD Monitor
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || electronic-servicing.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3745 seconds